CONTENTS DEEP ALARM GENERAL INTRODUCTION TO B&G NETWORK... 2 ENABLING/DISABLING THE DEEP ALARM...22 INTRODUCTION TO NETWOR
SPEED AND LOG CALIBRATION Before Network QUAD is used for navigation the boat speed and log have to be calibrated to ensure accuracy for your install
METHOD 1. - MANUAL CALIBRATION - CAL This procedure requires a reference boat speed with which to compare the Network QUAD units displayed boat spee
METHOD 2. - MANUAL CALIBRATION - LOG CAL If the log or boat speed is in error by a known percentage then this method allows the calibration figure o
METHOD 3. - AUTOMATIC CALIBRATION - AUTO CAL This procedure will automatically and accurately calibrate the boat speed and log and is the recommen
Distance measuredon a chartStopStartRun 3Run 3StopStartRun 1Run 1StopStartRun 2Run 2ABORTING AUTO CALAUTOMATIC CALIBRATION PROCEDURE 610-HB-0503-05
RESETTING THE DEAD RECKONED DISTANCE This facility allows the Dead Reckoned (DR) distance log to be reset. The Network QUAD unit cannot display the D
USING THE DEPTH KEY The current water depth is permanently displayed in the bottom LCD area in metres, feet or fathoms. The unit is factory set to me
THE DEPTH DATUM - CAL The depth datum CAL is an offset calibration value used to determine the displayed information reference point. It is added to
SETTING THE DEPTH DATUM CAL zero, depth from transducer. CAL positive, depth from waterline. CAL negative, depth from keel. NOTE: If the CAL LOCK i
SETTING THE DEPTH UNITS The Network QUAD unit can be set to display depth in Metres, Feet or Fathoms. The selected units are used for displayed dept
GENERAL INTRODUCTION TO B&G NETWORK INTRODUCTION TO NETWORK QUAD The B&G Network range of instruments is designed to be used as individua
610-HB-0503-05 20 DEPTH ALARMS The display will show OFF if the alarm is disabled or the alarm value when enabled. The value will be displayed in
ENABLING/DISABLING THE SHALLOW ALARM Press DEPTH key to display the shallow alarm.Press SETUP key, the alarm state will be displayed.Press ENTER key,
ENABLING/DISABLING THE DEEP ALARM Press DEPTH key to display the deep alarm.Press SETUP key, the alarm state will be displayed.Press ENTER key, the a
610-HB-0503-05 23 USING THE ANCHOR ALARM The Anchor Alarm uses two adjustable alarm limits. The alarm will sound if the water is deeper or shallow
ENABLING/DISABLING THE ANCHOR ALARM Press DEPTH key to display ANCHOR ALARM Press SETUP key, to display alarm state.Press ENTER key, the alarm sta
ADJUSTING THE ANCHOR ALARM SHALLOW LIMIT Press DEPTH key to display anchor alarm. Press SETUP key twice to display the shallow value.Press EN
USING THE TIMER/TEMP KEY Press the TIMER/TEMP key to cycle through the options: TRIP LOG A reset log that can be displayed in Nautical miles or Statut
RESETTING THE TRIP LOG The Trip Log is reset to zero and starts again as soon as the ENTER key is pressed. Press TIMER key to display the TRIP
SETTING THE TIMERS AND LAP TIMER The Lap Timer can be used to `freeze' the displayed time w th any of the three Timers. Press the TIMER key
SETTING THE TEMPERATURE UNITS The sea temperature can be displayed in Celsius or Fahrenheit. Press TEMP key until the sea temperature is display
INTRODUCTION TO NETWORK QUAD CONT'D NETWORK QUAD DISPLAY UNIT The Network QUAD unit has three adjustable alarms: 1. Shallow water alarm 2
CALIBRATING THE TEMPERATURE SENSOR Temperature calibration should only be carried out when the built-in sea water temperature sensor (part of the sp
USING THE LIGHTS KEY he Network QUAD Display unit has 3 levels of illumination nd off, controlled by the LIGHTS key. It also changes the illumination
NETWORK ALARMS The Network QUAD unit has an internal buzzer that will sound when an alarm condition is met on a Network unit that has alarm functions
FAULT AND ERROR MESSAGES NETWORK PILOT FAULT DISPLAY (NOT QUAD UNIT) If the Network PILOT should have a fault the autopilot computer unit will send
INSTALLATION The display heads are supplied with a clip-in mounting bracket which allows for easy installation, access from behind is not necessary t
INSTALLATION DATA GasketBulkheadFit the gasket aroundthe mounting bracket82.0mm82.0mmMounting bracket Rubber GasketGasketDisplay UnitSun-coverSelf-tap
610-HB-0503-05 36SPECIFICATION HYSICAL PARAMETERS onstruction High impact ABS plastic indow Acrylic Display Back-lit Liquid Crystal Displa
EXAMPLES SYSTEMS USING NETWORK QUAD Only one Network QUAD unit should have speed and depth sensors connected to it and set to transducer mode. Up to
SELECTING THE DISPLAY MODE The Network QUAD unit has two operating modes. The correct mode must be selected for your Network system to operate proper
USING THE SPEED KEY Boat speed information is permanently displayed in the top area of the LCD. Press the SPEED key to cycle through the following o
CALIBRATION AND OPERATING PARAMETERS When current boat speed is displayed, press the SETUP key to cycle through the following options: DAMPING Th
SETTING THE DISPLAY DAMPING Damping allows the response time of the displayed speed value to be slowed down if it is to jumpy in rough weather, or t
SETTING THE SPEED AND LOG UNITS The Network QUAD can be set to display boat speed in Knots or MPH. If boat speed is in Knots then log is in Nautica
Comments to this Manuals